Installation and activation of pdfaPilot Server/CLI
pdfaPilot CLI (command line interface) may be used to analyse files or to analyse and convert to PDF/A (if possible).
For activating the SDK (software developer kit), please visit this page.
The command line version of pdfaPilot is available for the following operating systems:
- Mac (Intel): macOS , version 10.7 or newer, 64-bit-compliant
- Windows 7 or newer
- Windows Server 2008 R2 or newer
- Linux: The minimum required Linux OS versions are shown below (newer versions are always supported as well):
- Debian 7 (or derivates like Ubuntu 12.x)
- RedHat RHEL6 (or derivates like CentOS6)
- SuSE SLES11 (or derivates like OpenSuSE11)
- Note: other Linux distributions are also supported as well if the version of the glibc is at least v2.12. Please use the ldd --version command to find out the version of glibc that comes with your Linux system.
- Solaris (Sparc and Intel): Solaris 11 (v5.11) or newer
- AIX (PPC): AIX 6.1 (oslevel 6100-09) or newer
You can easily test if pdfaPilot CLI is working on your system: Just type pdfaPilot --help in the terminal.
There are 64 bit versions of pdfaPilot CLI available for MacOS, Windows and Linux. pdfaPilot CLI does also run on 64 bit systems if the required 32 bit compatibility packages are available.
at least 2 GB RAM
at least 10 GB of free Disk Space
pdfaPilot does not have extensive hardware requirements, so a decent computer should usually satisfy for processing PDF files. Concrete requirements depend very much on the complexity of the files and the operations to be performed. Some general recommendations are:
- For any PDF processes (checking and/or fixing) information about all PDF objects has to be available to the engine. The size of the RAM memory needs to be big enough for all such objects. If possible the size of the RAM should be not too small, especially for complex PDF files with many pages.
- Any operations will include reading and writing to "disc". Faster storage devices therefore speed up the process and processing will take advantage of using SSDs or similar.
- pdfaPilot allows for parallel processing. This will, however, only result in faster processing if the number of cores is higher than the number of parallel processes. It is recommended to have at least one additional core for system processes.
160 GB SATA hard disc
500 GB SATA SSD
Installing the software
To install the software start the pdfaPilot Server installer. The installation program will then take you through the necessary steps.
Extract all files from the archive to a destination folder of your choice.
Additional information is provided in <pdfaPilot CLI directory>/ReadMe.txt
Before callas pdfaPilot CLI can be used, the software has to be activated.
Request an activation code
Open a terminal window and change to your pdfaPilot CLI installation directory. Type:
pdfaPilot --keycode [--aws] <name> <company> <licenseCode>
||Name of licensee (e.g. "Registered User")
||Name of company (e.g. "User's company")
||Licence key obtained from the registration card or the License.pdf provided by callas or the reseller.
||For installation on Amazon Web Services (using Windows, Linux 32bit and 64bit)
The textual output of --keycode has to be send via e-mail to the e-mail address named in the text in order to receive an activation code from the registration server.
To make a request for a trial version, please use the keyword "trial" (for a pdfaPilot trial version) for this parameter
Activating pdfaPilot CLI
After receiving the automatic e-mail reply from the activation server, save the attached 'activation file' to the file system. Then use the following command:
pdfaPilot --activate <activation file>
If no response is received or in the event of an error, please contact firstname.lastname@example.org to determine the exact cause.
The Activation.pdf (or the content of the e-mail) can only be used for activation for 48 hours.
After this timeframe, a new Activation.pdf has to be requested from the activation server.
||Full path to Activation PDF
It is necessary to activate the received license file to get a permantent valid license file.
The license file received from the activation server must be activated within the timeframe listed in the license file.
The activated license file will be stored in the user-preferences when the normal activation (command above) is used.
To create an activated license file at a custom location, just use the following command:
pdfaPilot --activate <licence file> -o=<path to result folder/License.txt>
pdfaPilot CLI is searching for the license file at various folders:
- user-preferences-folder of actual user
- next to the pdfaPilot CLI binary
- cachefolder (if set)
- user-preferences-folder for all users (shared)
When using UNIX-based-systems the environment variable CALLAS_SYSTEM_PREFERENCES the path of the standard /usr/share/callas software/callas pdfaPilot CLI can be changed:
would result in the searchpath: /tmp/callas software/callas pdfaPilot CLI
It is highly recommended to use the option --cachefolder instead.
Time-limited trial version
After requesting and entering a trial activation code, pdfaPilot CLI can be tested without any restrictions. When the evaluation period has expired, processing PDF files will no longer be possible until you request and enter a new activation code.
Activation using the Standalone application
Using Windows and MacOS, also the activation dialog of the Standalone Application can be used for requesting an activation as well as using a Keycode or just for a trial version. Also the activation itself can be done using that Interface.
All activations (for Desktop and Server/CLI) can be done using this dialog.
Deactivate pdfaPilot using the CLI
As the activation (and the resulting license file) is bound to the hardware. It is necessary to deactivate a license on one machine before an activation takes place on the new machine.
pdfaPilot --deactivate <activation code>
||Unique identifier for each license
The respective license will be removed from the system
To complete the deactivation, the output of the command has to be sent manually to the activation server by e-mail.
The activation code for all license are listed using the status command:
Deactivation using the Standalone application
Similar to the deactivation using the CLI, the Desktop on Windows and MacOS can be used for deactivation.
The selected license will be removed from the system as well and the necessary e-mail to the activation server will be sent automatically.